Monthly Archives: June 2014

Features of high pressure Industrial Centrifugal blower Fan

High pressure, large volume, low noise and lightweight.
Made of aluminum alloy material, long low weight substantially, achieve the purpose of lightening.
Special blade design, high pressure, large air volume, low noise, long service life.
Special air conditioning ventilation, air volume control high stability, easy operation, (CX, TB, HTBRB application)
Style, complete, inventory, and rapid delivery.
In addition to the above characteristics generally,high pressure blower also has the following features:
1,with push-pull dual function, a dual-purpose machine, you can use the suction, or you can use hair dryer; there is a wind of the RB series high pressure blower, you can also use both suction and hair dryer, equivalent to a rotary vane vacuum pump function;
2,less oil or oil-free operation, the output of the air is clean;

Industrial Centrifugal Fan

Industrial Centrifugal Fan

3,relative to the centrifugal blower and air compressor, and its pressure is much higher, often centrifugal Industrial Centrifugal Fan more than a dozen times, most pressure up to 230KPA;
4,if the pump is complete die casting, and used the shock-mounted pedestal, its installed base requirements are very low, even normal without fixed base operations, very convenient and also save on installation costs and the installation cycle;
5,compared to other types of  Industrial Centrifugal Fan, such as ARIMA Industrial Centrifugal Fan,its operation,quieter,bigger power significantly,it would have shown more than 5.5KW;
6, maintenance-free to use; its loss just two bearings, within the warranty period, with almost no maintenance;
7,high pressure blower mechanical wear and tear is very small, because other than bearings, no mechanical contact with some of the other, so the course is very long service life, as long as it is under normal conditions of use, 3-5 is free of problems. This is also the high-pressured air blower are the biggest reasons.

Related Industrial Centrifugal Fan products website:
http://www.simoblower.com

KPD series electric transfer cart operation points for attention

Xinxiang hundred percent group is a professionalelectric KPD series, track tractor and other equipment manufacturers, the company produces electric equipment sold at home and abroad, customers get the praise.

transfer cart

transfer cart

When the KPD series electric power Cabinet voltage to 36V depended mainly on the ground, and then to provide electricity to the conductive tracks, through vehicle electrical and friction sliders and other equipment to provide electricity to a step-up transformer, voltage increases until we finally reached the vehicle electric control cabinet devices.

And share in following KPD series transfer cart to some places that need attention:
1. the electric conductive surfaces require require regular cleaning, polishing, so as to ensure normal conductive surface conductive. If electric conductive grease, rust, dust and other insulators, in conductive may cause an exception, so that the machine does not power up properly, thus affecting the normal work.
2. in order to ensure the transfer cart to work properly, ground power supply Cabinet voltage meter and power indicated on the table to ensure that normal. Under normal circumstances, slightly too much voltage 36V belongs to the normal voltage. Ammeter indicates smaller is normal behavior, but to ensure that the meter indicator is normal, no swing.
3. when using the electric load, to maintain the flat Center of balance. Goods placed best parted down the Middle, uninstall Uninstall when the ends of the goods, unload after the middle of the, so you can effectively keep the transfer cart balance in order to better work.

Auto Truck Air Conditioner usage notes

1,Only ventilation is not needed when cooling fan can only be switched on without the need to switch on the compressor.

Truck Air Conditioner

Truck Air Conditioner

2,use Truck Air Conditioner when the cars stopped, the condenser fan is started and working time should not be too long, so condenser pressure is too high and damage the refrigeration system and to prevent excessive battery discharge.
3,when the engine load is too large, and should be temporarily off the Truck Air Conditioner, so as to avoid engine overheating affecting road.
4,if a car parked in the Sun for a long time, when it’s hot inside the car, after turning on the Truck Air Conditioner, open a window, inside hot air discharged and then close the window.
5,when the use of Truck Air Conditioner, temperature switches should be avoided when the maximum cold position, while the wind at low wind speeds, to prevent frost on the evaporator.
6,periodic cleaning of the condenser, use compressed air or cold water for washing, prohibited the use of steam cleaning, so as not to cause an increase in pressure in the condenser failure.
7,no speed control device for vehicle Truck Air Conditioner systems, be sure to start the engine, rear Truck Air Conditioner, to avoid difficulty in starting.
8,the air filter should be replaced once every 3 months anti-odor filter.
9,when parking the car in the summer, you should try to avoid Sun
first of all need to declare that cannot compare results with home Truck Air Conditioner car Truck Air Conditioner. Under what conditions may be determined in Truck Air Conditionerner ditioning refrigerating effect is not ideal? There is no uniform standard. Generally speaking, in the case of car door and window seal and body insulation and good Truck Air Conditioner engine speed of 1000 rpm speed after running 30 minutes, both inside and outside temperature difference of 10 ° c or above, below 10 ° c can be judged to be satisfactory.

Links to related  products

Truck Air Conditioner URL:http://www.coruntech.com

Seal butterfly’s valve to the inserting type hard pneumatically

D673H pneumatic right inserting type hard sealed butterfly  valve:
D673H pneumatic wafer butterfly valve with a “u” shaped stainless steel sealing ring, precision elastomeric sealing rings and polished the eccentric disc three-dimensional contact. Solves the eccentric butterfly valve sealing surface of the opening and closing moments 0 ° ~10 ° still in the ills of sliding friction, realize sealing face Butterfly plate in the opening moments that separate, close contact with sealing effect, aim to prolong the service life and optimum sealing performance. Are commonly used in medium temperature ≤550 c, metallurgy, electric power, petroleum, chemicals, air, gas, inflammable gas and corrosive mediums, such as water supply and drainage pipes, is the best device for regulating the flow and block fluid.

pneumatic wafer butterfly valve
II, and D673H pneumatic on clip type hard sealed butterfly valve of features:
1, and the butterfly valve structure simple, and compact, and weight light, and easily installation and demolition, and maintenance convenient;
2, and this butterfly valve used stainless steel “u” type sealed circle, has must of elastic regardless of in high temperature, and cryogenic of situation Xia, it and Butterfly Board are has excellent of sealed sex;
3, and this butterfly valve of three dimensional eccentric from, After strictly of calculation, “u” type sealed circle and Butterfly Board almost no mill wipe, using life long, and has more shut more tight of function;
4, and Butterfly Board key cover used heap welding cobalt Base carbide, sealed surface resistance wear, using life long;
5, and this butterfly valve structure unique, “switch” only needed turned valve Rod 90 ° can completed. Flexible, convenient, labor-saving operation, no influence of high and low pressure, the sealing property is reliable;
6, high temperature resistance, low temperature resistance, corrosion resistance;

Links to related  products

pneumatic wafer butterfly valve URL:https://www.facebook.com/waferbutterflyvalve